Physico-Chemical and Microstructural Analysis of Al-Mg-Si Alloy Matrix Composites Reinforced Groundnut Shell ash Particulates
Article Sidebar
Main Article Content
Metal matrix composites are an appealing alternative to monolithic metals for a variety of technical applications due to their superior mechanical and physical properties throughout a broad range of operating conditions. In the current study, different weight percentages of 150 µm groundnut shell ash (GNSA) particles (2.5%, 5%, 7.5%, 10%, 12.5%, 15%, 17.5%, 20%, 25% and 30%) were used to reinforce Al-Mg-Si alloy. Stir-casting was used to prepare the composite in a permanent mild steel mould. A number of the composites' physical, chemical, and microstructural characteristics (density, percentage porosity, XRF and SEM-EDS) were assessed, compared, and analysed with those of the matrix alloy. Oxides that could enhance the composites' mechanical, physical, and structural qualities were found during the structural assessment evaluation of the reinforcement. The microstructural analysis demonstrated that the GNSA reinforcements' secondary phase was uniformly distributed throughout the primary phase of the Al-Mg-Si alloy matrix. The added GNSA particles decreased the produced composite's density below that of the base alloy, and the percentage porosity of the composites rose as the groundnut shell ash content increased and remained within the upper limit allowed for cast aluminium metal matrix composites. The composites that were created showed evidence of intermetallic compound formation.
Downloads
Downloads
References
J. Agunsoye, S. Talabi, S. Bello and I. Awe, "The effects of cocos nucifera (coconut shell) on the mechanical and tribological properties of recycled waste aluminium can composites," Tribology in Industry, vol. 36, no. 2, pp. 155-162, 2014.
M. Abdulwahab, R. Dodo, I. Suleiman, A. Gebi and I. Umar, "Wear Behavior of Al-7%Si-0.3%Mg/melon shell ash particulate composites," Heliyon, vol. 3, no. 8, art. ID e00375, 2017. DOI: https://doi.org/10.1016/j.heliyon.2017.e00375
K. K. Alaneme and B. J. Bamike, "Characterization of mechanical and wear properties of aluminium based composites reinforced with quarry dust and silicon carbide," Ain Shams Engineering Journal/Ain Shams Engineering Journal, vol. 9, no. 4, p. 2815–2821, 2018. DOI: https://doi.org/10.1016/j.asej.2017.10.009
Apasi, D. Yawas, S. Abdulkareem and M. Kolawole, "Improving mechanical properties of aluminium alloy through addition of coconut shell-ash," Journal of Science Technology, vol. 36, no. 3, pp. 34-43, 2016. DOI: https://doi.org/10.4314/just.v36i3.4
K. K. Alaneme, B. O. Ademilua and M. O. Bodunrin, "Mechanical properties and corrosion behavior of aluminium hybrid composites reinforced with silicon carbide, and bamboo leaf ash," Tribology in Industry, vol. 1, no. 35, pp. 25-35, 2013.
K. Alaneme, T. Adewale and P. Olubambi, "Corrosion and wear behaviour of Al–Mg–Si alloy matrix hybrid composites reinforced with rice husk ash and silicon carbide," Journal of Materials Research Technology, vol. 3, no. 1, pp. 9-16, 2014. DOI: https://doi.org/10.1016/j.jmrt.2013.10.008
R. Arunachalam, .. Krishnan and R. Muraliraja, "A review on the production of metal matrix composites through stir casting–Furnace design, properties, challenges, and research opportunities," Journal of Manufacturing Process, vol. 42, pp. 213-245, 2019. DOI: https://doi.org/10.1016/j.jmapro.2019.04.017
P. K. Bannaravuri and A. K. Birru, "Strengthening of Al-4.5%Cu alloy with the addition of Silicon Carbide and Bamboo Leaf Ash," International Journal of Structural Integrity, vol. 10, no. 2, p. 149–161, 2019. DOI: https://doi.org/10.1108/IJSI-03-2018-0018
V. Chak, H. Chattopadhyay and T. Dora, "A review on fabrication methods, reinforcements and mechanical properties of aluminum matrix composites," Journal of Manufacturing Processes, vol. 56, pp. 1059-1074, 2020. DOI: https://doi.org/10.1016/j.jmapro.2020.05.042
H. Chauhan and C. A. Irfan, "Variation of mechanical properties (tensile strength h & microstructure) of Al6061 / (Al2O3 and fly ash), hybrid metal matrix composite produced by stir casting," International Research Journal of Engineering and Technology, vol. 4, no. 7, pp. 2407-2414, 2017.
F. O. Edoziuno, A. A. Adediran, B. U. Odoni, O. G. Utu and A. Olayanju, "Physico-chemical and morphological evaluation of palm kernel shell particulate reinforced aluminium matrix composites," Materials Today: Proceedings, p. 652–657, 2021.
F. O. Edoziuno, B. U. Odoni, F. I. Alo and C. C. Nwaeju, "Dry Sliding Wear And Surface Morphological Examination of An Aluminium Matrix Composite Reinforced With Palm Kernel Shell," Acta Metallurgica Slovaca, vol. 26, no. 2, p. 54–62, 2020. DOI: https://doi.org/10.36547/ams.26.2.537
R. Fakhir and R. J. Shawnim, "The Effectiveness of Reinforcement and Processing on Mechanical Properties, Wears Behaviour and Damping Response of Aluminium Matrix Composites," High Temp. Mater. Proc,, pp. 327-939, 2019.
Gireesh, P. K. Durga, K. Ramji and P. Vinay, "Mechanical characterization of aluminium metal matrix composite reinforced with aloe vera powder," Materials Today: Procedings, vol. 5, no. 2, pp. 3289-3297, 2018. DOI: https://doi.org/10.1016/j.matpr.2017.11.571
K. Hemanth, B. Siddeswarappa and P. K. Prasanna, "A Review on Mechanical Behavior of Aluminium 6061 Reinforced with different Agro Ashes," International Journal for Research in Applied Science & Engineering Technology (IJRASET), vol. 8, no. 12, pp. 382-388, 2020. DOI: https://doi.org/10.22214/ijraset.2020.32512
Y. S. Idawu, K. Auwal, T. M. Abdullahi and M. Z. Sirajo, "Evaluation of Mechanical, Microstructures and Wear Behaviours of Aluminium Alloy Reinforced with Mussel Shell Powder for Automobile Applications," Journal of Mechanical Engineering, vol. 67, no. 1-2, pp. 27-35, 2021. DOI: https://doi.org/10.5545/sv-jme.2020.6953
P. P. Ikubanni, M. Oki, A. A. Adeleke and P. O. Omoniyi, "Synthesis, physico-mechanical and microstructural characterization of Al6063/SiC/PKSA hybrid reinforced composites," Scientific Reports, vol. 11, no. 1, 2021. DOI: https://doi.org/10.1038/s41598-021-94420-0
H. Kala, K. Mer and S. Kumar, "A review on mechanical and tribological behaviors of stir cast aluminum matrix composites," Procedia Materials Science, vol. 6, pp. 1951-1960, 2014. DOI: https://doi.org/10.1016/j.mspro.2014.07.229
P. P. Kulkarni, B. Siddeswarappa and K. S. H. Kumar, "A Survey on Effect of Agro Waste Ash as Reinforcement on Aluminium Base Metal Matrix Composites," Open Journal of Composite Materials, vol. 09, no. 03, p. 312–326, 2019. DOI: https://doi.org/10.4236/ojcm.2019.93019
B. P. Kumar and A. K. Birru, "Microstructure and mechanical properties of Aluminium metal matrix composites with addition of bamboo leaf ash by stir casting method," Trans. Nonferrous Met. Soc. China (English Ed.), vol. 27, no. 12, p. 2555–2572, 2017. DOI: https://doi.org/10.1016/S1003-6326(17)60284-X
L. Lancaster, M. Lung and D. Sujan, "Utilization of agro-industrial waste in metal matrix composites: Towards sustainability," International Journal of Environmental, Ecological, Geomatics, Earth Science and Engineering, vol. 7, no. 1, pp. 35-43, 2013.
S. Nallusamy, S. Saravanan, V. Kannarasu and M. R. Narayanan, ""Experimental Analysis on Reinforced Aluminium Metal Matrix with Boron Carbide, Graphite and Fly Ash Chemical Composites"," Rasayan Journal of Chemistry, 2017.
K. Padmavathi, R. Ramakrishnan and K. P. Kumar, "Aluminium Metal Matrix Composite-An Insight into Solid State and Liquid State Processes," Applied Mechanics and Materials, pp. 766–767, 234–239, 2015. DOI: https://doi.org/10.4028/www.scientific.net/AMM.766-767.234
T. Rajmohan, K. Palanikumar and S. Ranganathan, "Evaluation of mechanical and wear properties of hybrid aluminium matrix composites," Trans. Nonferrous Met. Soc. China 23, pp. 2509-2517, 2013. DOI: https://doi.org/10.1016/S1003-6326(13)62762-4
M. Satheesh and M. Pugazhvadivu, "Investigation on physical and mechanical properties of Al6061-Silicon Carbide (SiC)/Coconut shell ash (CSA) hybrid composites," Physica. B, Condensed Matter, 572, p. 70–75, 2019. DOI: https://doi.org/10.1016/j.physb.2019.07.058
V. Sharma, R. Singh and R. Chaudhary, "Effect of fly ash particles with aluminium melt on the wear of aluminium metal matrix composites," Engineering Science and Technology, an International Journal, vol. 20, no. 4, p. 1318–1323, 2017. DOI: https://doi.org/10.1016/j.jestch.2017.08.004
F. Tugiman, F. Taher, M. Hasibuan and Suprianto, "The analysis of composite properties reinforced with particles from palm oil industry waste produced by casting methods," IOP Conference Series: Materials Science and Engineering, Vols. 277, art. ID 012028, 2017. DOI: https://doi.org/10.1088/1757-899X/277/1/012028
R. Umunakwe, D. J. Olaleye, A. Oyetunji, O. C. Okoye and I. J. Umunakwe, "Assessment of some mechanical properties and microstructure of particulate periwinkle shell-aluminium 6063 metal matrix composite (PPS-ALMMC) produced by two-step casting," Nigerian Journal of Technology, 36(2), 421, 2017.
Usman, R. A., M. Hassan and N. Waziri, "A comparative study on the properties of Al-7%Si-rice husk ash and Al-7%Si-bagasse ash composites produced by stir casting," International of Journal of Engineering Sciences, vol. 3, no. 8, pp. 1-7, 2014.
Odoni, B. Onyekpe and O. Awheme, "Evaluation of Palm Kernel Shell Ash Particle Reinforced Aluminium 6061 Alloy Matrix Composites Using Physio-Chemical and Microstructural Methods," Journal of Materials Engineering, Structures and Computation 3(1) 2024, vol. 3, no. 1, pp. 52-61, 2024.
F. Edoziuno, A. Adediran, B. Odoni, O. Utu and A. Olayanju, "Physico-chemical and morphological evaluation of palm kernel shell particulate reinforced aluminium matrix composites," Materials Today: Proceedings, 2020. DOI: https://doi.org/10.1016/j.matpr.2020.03.641
O. Oladele and A. M. Okoro, "The effect of palm kernel shell ash on the mechanical properties of as-cast aluminium alloy matrix composites," Leonardo Journal of Sciences, no. 28, pp. 15-30, 2016.
R. Umunakwe, D. Olaleye, A. Oyetunji, O. Okoye and I. Umunakwe, "Assessment of the density and Mechanical Properties Of Particulate Periwinkle Shell-Aluminium 6063 Metal Matrix Composite (PPS-Almmc) Produced By Two-Step Casting," Acta Technica Corviniensis, vol. 36, no. 2, pp. 83-90, April 2017a. DOI: https://doi.org/10.4314/njt.v36i2.14
K. Alaneme and B. U. Odoni, "Mechanical properties, wear and corrosion behavior of copper matrix composites reinforced with steel machining chips," Engineering Science and Technology an International Journal, vol. 19, no. 3, p. 1593–1599, 2016. DOI: https://doi.org/10.1016/j.jestch.2016.04.006
P. Brouwer, "THEORY OF XRF. PANalytical B.V.," 2010. [Online]. Available: https://www.iotcco.com/uploads/VirtualTeaching/Articles/PANanalytical. [Accessed 30 July 2024].
R. P.-C. M. Escalera-Lozano, M. A. Pech-Canul, M. Montoya-Dávila and A. Uribe-Salas, "The Role of Mg2Si in the Corrosion Behavior of Al-Si-Mg Alloys for Pressureless Infiltration," The Open Corrosion Journal, pp. 73-79, 2010. DOI: https://doi.org/10.2174/1876503301003010073
N. Chandla, K. Yashpal, C. Jawalkar and N. Suri, "Review on analysis of stir casting aluminium metal matrix composites from agro-industrial waste," i-Manager’s Journal of Materials Science, vol. 5, no. 2, pp. 35-46, 2017.
All articles published in our journal are licensed under CC-BY 4.0, which permits authors to retain copyright of their work. This license allows for unrestricted use, sharing, and reproduction of the articles, provided that proper credit is given to the original authors and the source.